LSG Communications AB

SPE EXPERT 1.3K-FA 1 KW 1.8-50MHz (utan AT)

SPE EXPERT 1.3K-FA 1 KW 1.8-50MHz (utan AT), Amatörradio, Slutsteg HF VHF

Dubbelklicka på bilden ovan för att se bilden i originalstorlek

Zooma ut
Zooma in

Fler bilder

  • SPE EXPERT 1.3K-FA 1 KW 1.8-50MHz (utan AT), Amatörradio, Slutsteg HF VHF
  • SPE EXPERT 1.3K-FA 1 KW 1.8-50MHz (utan AT), Amatörradio, Slutsteg HF VHF

Lagerstatus: Ej i lager.

Exkl. moms:
26 000,00 kr
Inkl. moms:
32 500,00 kr
Datablad 1.3K-FA
Manual 1.3K-FA
Produktbeskrivning
  • The smallest in its class.
    Built-in Power supply..
    Dimension: L 28, H 12, P 38 cm (11.02” W,. 4.72” H, 14.96” D) (connectors included).
    Approx. weight without ATU is about 7.5 Kg.(16.5lbs). With ATU about 9,5 Kg (20.9 lbs).
  • The most technologically advanced in the world
    Two powerfull CPUs are used.
    Over 35,000 lines of software for performance that cannot be found in any other amplifier.
  • Fully Automatic
    Easy connection with all models "ICOM, YAESU, KENWOOD, TEN-TEC, FLEX-RADIO, ELECRAFT" for immediate management of the bands, antennas.
    Same performance with all makes and some homemade rigs.
    The operator has to only move the “Frequency Tuning Knob” of the transceiver !!
  • Wide frequency coverage
    1.8 MHz to 50 MHz including WARCs.
    Where permitted 60 m. full power and 300 W +/- 1dB  typ. on 4 m. (70 MHz).
  • Fully solid state
    Up to 1.5 (1.3 typ.) KW pep SSB, CW out; 50 MHz included.
    MAX , MID (800 W) or LOW (450 W) power selected according to the operator’s SSB/CW power requirement, for digital modes and for linear protection (automatic).
    No warmup time, immediately ready!
    Virtually limitless life of the amplification device. Only one LD / MOSFET used.
  • SO2R
  • Two inputs available.
    SO239 connectors.
  • High power gain (up to 14.5 dB).
    In “OPERATE“ the required drive power is automatically set with the ALC connection. And in “STANDBY“ the exciter is automatically reset to full power.
  • Very clean and low distortion output:
    Spurious emissions FCC compliant.
    3rd order distortion (two tone test) from -30 to -35 dB typ
  • Input 50 ohm always perfectly matched
    The same protection is realized in two different ways:
    · Via hardware circuits (HW) to assure great speed.
    · Via the software (SW), to assure great accuracy.
    Thanks to the sophisticated software, the transmit relay changeover is carried out with zero current on the contacts.
  • Full break-in operation (QSK)
  • Quiet operation.
    Linear management of the speed of the cooling fans of the heatsink.
    The amplifier develops a significant amount of heat that must be removed.
    Therefore, every precaution is used to keep the fan noise at the lowest possible level. Fan noise is significantly lower than with tube type amplifiers.
  • Continuous use
    “MAX” mode: SSB / CW unlimited.
    Automatically switches to “MID” if in “MAX” a continuous signal (RTTY) is transmitted for more than 15 sec.
    “MID” and “LOW” modes, RTTY unlimited.
  • Switching power supply.
    Continuously operable at inputs between 100 – 255 Vac, 47-63 Hz. (100-120 Vac may cause slightly reduced output power).
    PFC (Power Factor Correction).
  • The linear can be switched ON / OFF by switching the exciter ON / OFF.
  • Fully remotable.
  • With a large LCD display, it is possible to have a great deal of information:
    Watts pep out, Vpa, Ipa, Watts, Power gain, Temperatures, SWR (after and before the ATU), Input setting, CAT setting, Band and other indications including the alarms log.
  • Easy to operate
    Powerful and sophisticated software gives you a user-friendly unit.
  • USB / RS232 ports:
    For remote control.
    For new software releases download.
  • Easy transportation
    A sturdy, nice looking carry-bag is supplied for “QSY, FIELD DAY, DX’ PEDITIONS etc.“.
  • Certifications :
    CE, FCC.